Smart Swap® Instructions (valid Version 3.2 or later)

Smart Swap is a patented feature unique to Island that can save install time and hassle. Note that not every install is a candidate to use this feature. Smart Swap is used only when replacing an existing router and only when it’s advantageous to retain existing IP address schemes including those of VLANs. Note that a successful Smart Swap requires that steps are followed in the exact sequence below.

YOUR EXISTING NETWORK, AT MINIMUM, SHOULD INCLUDE:

  • The modem or combo unit supplied by your ISP

  • A router, referred to as the “existing” router in these steps

  • WiFi mesh or access points (APs) installed according to the respective manufacturer’s instructions

  • An Ethernet switch (any brand; required if your network includes more than 1 wired device)

To Get Started:

• Wired Router • Switch

Step 1:

Power up Island. Wait about 30 seconds for the light to turn from white to blue.

Step 2:

Within 5 minutes of powering up Island, plug Island into the switch. Within seconds, Island’s Smart Swap feature learns the existing network addresses.

If connecting to the existing LAN does not occur during this 5 minute window, Smart Swap will not succeed.

Important: This is now your LAN port. Note the port number.

Note: If there are VLANs on the network, ensure you are connecting Island to a trunk port on the switch.

Step 3: Continue using either:

  • The web app (requires a laptop and Ethernet cable) or

  • The mobile app (requires installed and accessible WiFi)

If using the web app

  1. Plug a laptop into any open port on the Island.

  2. Browse to my.islandrouter.com.

  3. Choose “Initialize” on the app screen.

If using the mobile app

  1. Download the Island app from the App Store.

  2. Launch the app.
    Note: If the mobile device you are using has been previously used to setup other Islands, the app will open to either a “home” island or a list of Islands. If a list, choose any Island, and in both cases, go to Tours and select Discover to connect to the new uninitialized Island. If you have cleared the “home” Island designation, the app will either go directly to Discover or will start up in Tours if multiple Islands are remembered. In every case, you will be able to connect to the new uninitialized Island.

  3. If you had previously made a backup of any Island on the mobile device, you will be prompted to Initialize or Restore. Choose Initialize. If a previous backup does not exist, the app will go directly to the following setup prompts.

Set up Steps Common to Web and Mobile App:

Step 4:

Reply to the prompts beginning with name your Island, name the device from which you are connecting to this Island, first user setup, and so on, making sure to leave Geek mode enabled.

Step 5:

Enter and confirm a PIN for the Island, making sure to take measures to remember it. If you don’t select “Remember PIN on this device”, you may need to re-enter the PIN at various points in the process.

Step 6:

As soon as the PIN Is confirmed, the app restarts and immediately checks if the firmware on your Island is current. If prompted to update, respond “Yes”.

Step 7:

Depending on the firmware version, the Island may reboot itself at this point.

Step 8:

At the conclusion of any firmware update, the main dashboard displays. At this time, if any port (interface) is in use but the port is in “fully automatic” mode, meaning that the interface mode has not been “locked” in, there will be an amber notice icon to the top left of the large Island icon. Ignore this notice for now. (If you click on it, a message box appears asking you to lock in the port modes. Do not click on “LOCK” at this time. Click outside the box or wait ten seconds for the message to disappear.)

Step 9:

Only if using the mobile app, close the app now.

Step 10:

Identify the cable connecting the WAN port on the existing router. Unplug it from the existing router and plug it into any port on the Island (either a 2.5G port or 10G port with appropriate transceiver).

Important: This is now your Island WAN port. Note the port number.

Step 11:

Reboot the modem and wait for the modem to come back up. (This can take some time, depending on the modem.)

Note: Some modems have an internal battery backup. If so, remove the battery before reboot.

Step 12:

Disconnect the existing router from the network and give Island a minute or so to take over the disconnected router’s IP address and assimilate existing device IP addresses. The Smart Swap procedure is then complete.

Step 13:

ONLY if using the mobile app, open the app now.

Step 14:

From the main dashboard, click on the amber notice icon to the top left of the large Island icon. A message box opens asking you to lock in the port modes. After ensuring that the recommendations for the interface modes are correct, you should now select “LOCK”. (This action can also be accomplished by going to the Network screen under the top left hamburger menu, where you will be prompted to lock ports if needed.)

 

The Island install is now complete.